ATS RC Planes

RC Airplane Servos and Micro Servos

 

 

 Hitec Servo

 

HS-82MG Micro Servo

 

Only $21.99

 

Hitec/JR/Airt. Z

 

A new stronger motor and updated electronics for more precise centering. The HS-82MG is perfect for smaller aircraft and helicopters where a durable gear train is required.

  • Torque 38.88 oz/in (2.8kg.cm) @ 4.8 volt

  • Torque 47.22 oz/in (3.4kg.cm) @ 6.0 volt

  • Speed 0.12 se3c/60  at 4.8 volt

  • Speed 0.10 sec/60 at 6.0 volt

  • Size 29.8 x 12.0 x 29.6mm

  • Size 1.17 x 0.47 x 1.16 in

  • Weight 19.0g (0.66oz)

  •  Motor Type: 3 Pole

HS-82MG Micro Servo

Only $21.99

 

 

 

 

 Hitec Servo

 

HS-55 Micro Feather Servo

 

Only $13.99

 

Hitec/JR/Airt. Z

HS-55 Hitec Micro Feather Servo

Details at 6.0 volt

  • Torque 18 oz/in

  • Speed/60 0.14 sec

  • Size 0.9x .46x .95 in

  • Weight 8.0g (0.28oz)

HS-55 Micro Servo

Only $13.99

 

 

 

 

 

 

 

 

WAYPOINT  W-092-SH

 Precision Sub Micro 9.2 Gram  Servo

 

For HIGH SPEED /HELI

 

Only $17.80

W-092-SH  

High Speed for Mini Helicopter /E3D
Weight : 9.4g/0.36oz
Torque : 4.8V 1.3kg-cm / 17oz-in
Speed : 4.8V/0.09sec/60?
Size (mm) : 24.5x11.5x22.5
Size (inch) : 0.98x0.45x0.90
Motor type : 3-Pole Ferrite
Gear type : Plastic
Ball Bearing: Single, Top


W-092-SH 9.2 G Sub-Micro

High Speed/Heli   Servo

Only $17.80

 

 

WAYPOINT  W-092

 Precision Sub Micro 9.2 Gram  Servo

Only $16.80

Great for use on the Hyperion Piper Cub 10E, Chipmunk 10E, YAK 55SP 10E, CAP 232, Extra 300L & Sukhoi SU-31

W-092

 

Weight : 9.2g /0.34oz
Torque : 4.8V 1.5kg-cm / 22oz-in
Speed : 4.8V/0.12sec/60
Size (mm) : 24.5x11.5x22.5
Size (inch) : 0.96x0.45x0.90
Motor type : 3-Pole Ferrite
Gear type : Plastic


W-092 Sub Micro Servo

 

Only $16.80

 

 

Waypoint CONNECTOR / COMPATIBILITY NOTES:

All Waypoint Servos (except 038CL-JST) come with JR/Hitec type connectors.

JR, Hitec, and newer Airtronics connectors are freely interchangeable for both male and female. The Futaba and JR/Hitec male connectors (as found on a servo) are also interchangeable, except that the Futaba has a small tab running along one side. The fact that this tab is missing on JR connectors poses no problem for Futaba Rx owners, as the servos will plug in just fine. All servos and receivers on the market today use the same wiring arrangement, so you don't have to worry about polarity being wrong. For almost everyone, our JR/Hitec servo connectors will work fine just as the are.

To use Waypoint servos (with JR-Hitec type connector) in an older Sanwa receiver which fits the connector, you would need to swap the positive and negative wire positions in the JR connector on the Waypoint servo to match the Airtronics wiring.  If you want to use an older Airtronics servo with any of the receivers, we recommend that you buy a male JR-Hitec connector (made by GWS) and solder it to the Airtronics servo wires with the correct polarity.

 

***We Gladly Accept Visa, MasterCard, Discover***

American Express & Electronic Checks Using Paypal

[Home] [Support]  [Ordering Info]  [Company Info]  [Contact Us]  [Email Us]